Your Message

With the exploration and innovation of Bebon people, DEN gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel, and established our own Machining processing center in order to meet customer's diverse requirements.




S50C (JIS ) Worldwide equivalent grades

S50C (Japan, JIS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product S50C on line

Reply
S50C steel

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S50C can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier[email protected]

Reply
S50C Plate 1050CK50GB50#Carbon Steel Supplier

1050 Carbon Steel / C50 Carbon Steel / 760 Carbon Steel is characterised by good strength and impact properties, with good machinability and reasonable weldability in the as supplied condition.   It has a low through hardening capability with sections up to around 60mm only generally recommended as suitable for through hardening and tempering.

Reply
S50C Carbon Steel JIS G4051 S50C steel plate Special

S50C Carbon Steel is one mainly of high carbon steel, for the high strength medium carbon steel, the cold work plasticity is low, the welding performance, the hardenability are bad, but non temper brittleness, cutting value still permissible.

Reply
S50C Plate S50C Carbon Steel Plate 1050 Carbon Steel

Description. Characterised by good strength and impact properties, with good machinability and reasonable weldability in the as supplied condition. 1050 has a low through hardening capability with sections up to around 60mm only generally recommended as suitable

Reply
S50C Carbon Steel Supplier & Stockist New Arise Metal

S50C Carbon Steel is steel grade in standard JIS G4051 JIS S50C Steel Grade is one steel grade material in JIS G4051, which is standard specification of carbon steels for Machine Structural use, such as Hot Rolling or Hot Forging Tool Steels .

Reply
S20C Mild Steel JIS Standard carbon structural steel (JIS

OTAI SPECIAL STEEL Supply in S20C steel round bar, plate, sheet, square bar, flat bar, pipe since 2007.we have a lots s20c steel stock. S20C flat Steel bar is a high quality Quenched and Tempered Carbon Structural steel, It belong to the high quality low carbon, Low carbon chromium, molybdenum, nickel case hardening steel.

Reply
S45C Steel For Machine Structural Use JIS G4051 Special

JIS S45C Steel is a medium strength steel. Suitable for shafts studs, keys etc. Available as rolled or normalised. JIS S45C machinery steel are usually supplied as square bar, or round bar or flat. JIS Steel S45C is excelling in weldability & machinability , and S45C steels can be

Reply
S50C Hot Rolled Steel Bar XC55 Steel Bar ssroundbar

S50C Hot Rolled Steel Bar is very resistant to corrosion and is used for this purpose in industry, S50C Hot Rolled Steel Bar is widely used for plating steel components. S50C Hot Rolled Steel Bar is a most useful material but it is very expensive

Reply
S45C (JIS ) Worldwide equivalent grades Steel Number

S45C (Japan, JIS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt

Reply
S50c Steel, S50c Steel Suppliers and Manufacturers at

About 11% of these are steel sheets, 2% are steel round bars, and 1% are steel strips. A wide variety of s50c steel options are available to you, such as aisi, astm. You can also choose from steel plate, steel coil. As well as from high strength steel plate, wear resistant steel. And whether s50c steel is

Reply
JIS G4051, Carbon Steels for Machine Structural Use

JIS S50C Carbon Steel is one steel grade material in JIS G4051. S50C carbon steel are generally use to make mechanical parts, like spring, gear, tension bar, the roller, the axis, the load spindle etc.

Reply
P20 And S50c Steel, P20 And S50c Steel Suppliers and

A wide variety of p20 and s50c steel options are available to you, such as hot rolled. You can also choose from aisi. There are 3,532 p20 and s50c steel suppliers, mainly located in Asia. The top supplying countries are China, Taiwan, China, which supply 99%, 1% of p20 and s50c steel respectively.

Reply
S45C BEBON steel

BEBON steel is professional S45C steel suppliers ,we also can supply S35C,S40C,S50C,S55C,please contact us if you need Bebon International is a professional S45C steel exporter and

Reply
S45C (JIS ) Worldwide equivalent grades Steel Number

S45C (Japan, JIS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt

Reply
S50c Steel Specification, S50c Steel Specification

offers 100 s50c steel specification products. About 9% of these are steel sheets, 1% are steel round bars. A wide variety of s50c steel specification options are available to

Reply
S45C Carbon Steel 760 Carbon Steel Malaysia CK45

1045 Carbon Steel 1045 is a medium tensile low hardenability carbon steel generally supplied in the cold drawn or turned and polished condition, with a typical tensile strength range 600 – 950 Mpa and Brinell hardness range 179 – 280. in either condition.Characterised by good strength and impact properties, with good machinability and reasonable weldability in the as supplied condition

Reply

Your Message